MGL Avionics Blaze FLIGHT-3 страница 33 Скачать руководство пользователя | Manualshive

Страница: 33 / 51

background image

Blaze FLIGHT-3 Operating Manual

Page 33

6 Error Messages

Unit settings CRC error. Load default settings to restore to factory defaults. If the error
message still persists then it could possibly be a non-volatile memory failure in which
case the instrument will then have to be returned to the factory.

Internal flash CRC error. The instrument does a firmware check on the program when
power is applied to the instrument . If the program is corrupt in any way then the internal
flash CRC error will be displayed. Reload the instruments firmware and load default
settings. If the error message still persists then it could possibly be an internal flash
memory failure in which

case the instrument will then have to be returned to the

factory.

Hobbs / Maintenance Timer CRC error. Try entering new values for the Hobbs meter and
Maintenance timer and see if the error message disappears. If the error message still
persists then it could possibly be a non-volatile memory failure in which case the
instrument will then have to be returned to the factory.

Calibration constants CRC error. The instrument could possibly have a non-volatile
memory failure in which case the instrument will then have to be returned to the factory.

Altitude sensor error. The instrument could have a faulty altitude sensor in which case
the instrument will then have to be returned to the factory.

Airspeed sensor error. The instrument could have a faulty airspeed sensor in which case
the instrument will then have to be returned to the factory. (Digital airspeed sensor
models only)

«
...
31
32
33
34
35
...
»

Содержание Blaze FLIGHT-3




















































Отзывы:

Нет отзывов

Похожие инструкции для Blaze FLIGHT-3

BL-Store Series

Бренд: Adexa Страницы: 7

Бренд: LXNAV Страницы: 9

Бренд: Thales Страницы: 703

MCP combo panel

Бренд: VRinsight Страницы: 24

Бренд: Icom Страницы: 2

Dreamflyer FMS df X-2

Бренд: FLIGHT MOTION SIMULATORS Страницы: 31

Бренд: Horizon Hobby Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды