Meyra 1.610 Скачать руководство пользователя

Страница: 18 / 104

Central leg support

Adjusting the height of the footplate

Remove the clamping screw (1) to adjust the height.
Telescope the footplate to the desired height and then se-

cure it with the clamping screw (1).

Angle adjustment of the central leg support

Remove the screw (2) for angle adjustment of the central

leg supports.

Swivel the leg support into a different position and remount

the screws (2).

☞

The leg support can be adjusted stepwise into
three further positions of 8.5° each.

Angle adjustment of the footboard

Remove the screw (3) for angle adjustment of the footboard.
Swivel the footboard into a different position and remount

the screws (3).

☞

The footboard can be adjusted stepwise into four
further positions.

Содержание 1.610









































































































Результаты поиска

Содержание 1.610

Отзывы:

Похожие инструкции для 1.610

Бренды по названию

Популярные бренды

Meyra 1.610, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание 1.610

Отзывы:

Похожие инструкции для 1.610

Бренды по названию

Популярные бренды