manualshive.com logo in svg

Meyer V-FORCE 7400 Series, Руководство оператора и каталог запасных частей, Страница: 11 / 88

Поделиться
Скачать
Meyer V-FORCE 7400 Series Скачать руководство пользователя страница 11

PB-74/7500

- 11 -

SAFETY DECALS

The Meyer Super Spreader is manufactured with operator safety in mind. Located on the manure spreader are
various decals to aid in operation and warn of danger or caution areas. Pay close attention to all decals on the
spreader.

DO NOT REMOVE ANY DECALS. IF DECALS ARE LOST, DAMAGED OR IF MANURE SPREADER IS

REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION

.

CAUTION: READ ALL DECALS ON THE SPREADER AND IN THIS MANUAL. KEEP THESE DECALS

CLEAN AND REPLACE ANY LOST OR DESTROYED DECALS. BECOME FAMILIAR WITH ALL TRACTOR
AND SPREADER CONTROLS.

TO PREVENT SERIOUS INJURY OR DEATH

DO NOT start, operate, or work on this machine without first carefully reading and
thoroughly understanding the entire contents of the operators manual. (Require the
same of all personnel who will operate this machine.)
If operators manual is lost, contact your nearest Meyer Dealership or write or call:

Please give your name, address, phone number, model and serial number of your 
machine. A manual will be furnished.
If you have any questions about operation or adjustments, and maintenance of this
machine, contact your Meyer Dealership or Meyer Mfg., Corp. before starting or
continuing the operation of this machine.

‡

‡

‡

MEYER MFG., CORP.

32%2;‡'RUFKHVWHU:,

3KRQH

CAUTION

46-0001-35

DECAL C - 46-0001-22

DECAL D - 46-0001-13

DECAL A - 46-3600-9

DECAL B - 46-0001-5

DECAL E - 46-0001-4

DECAL F - 46-0001-35

DECAL G - 46-0001-26

WARNING 

46-3600-9 

ROTATING DRIVE LINE

CAN CRUSH AND DISMEMBER

DISCONNECT AND LOCKOUT POWER
SOURCE BEFORE ADJUSTING
OR SERVICING UNIT.

FAILURE TO HEED WILL RESULT
IN DEATH OR PERSONAL INJURY

DO NOT OPERATE

WITHOUT SHIELD

IN PLACE

CAUTION 

SAFETY FIRST 

(Do Not Operate This Machine Without Reading These Instructions) 

Meyer Mfg. Corp. always takes the operator’s safety into consideration when designing farm machinery by covering
exposed moving parts for his protection; however, some areas cannot be guarded or shielded in order to assure proper
operation.

If any decal becomes damaged or lost, call your dealer or our plant for replacement.
Always use GENUINE MEYER replacement parts.

46-0001-22     1

Remember: The careful operator is the best operator. Most accidents are caused by human error. Certain precautions 
must be observed to prevent the possibility of injury or damage. 

IF THE MACHINE BECOMES CLOGGED, DISENGAGE POWER TAKE-OFF, REMOVE KEYS FROM TRACTOR, AND ALLOW
ALL MECHANISMS TO STOP BEFORE CLEANING.

KEEP HANDS, FEET, CLOTHING, AND HAIR AWAY FROM ALL MOVING PARTS WHEN MACHINE IS IN OPERATION,
LOOSE OR FLOPPY CLOTHING SHOULD NOT BE WORN BY THE OPERATOR.

STOP ENGINE, WAIT FOR ALL MOVEMENT TO STOP BEFORE LEAVING OPERATOR’S POSITION TO ADJUST,
LUBRICATE, CLEAN, OR UNCLOG MACHINES. UNLESS OTHERWISE SPECIFICALLY RECOMMENDED IN THE
OPERATOR’S MANUAL.

NEVER START THE MACHINE UNTIL ALL GUARDS AND SAFETY SHIELDS ARE SECURED IN PLACE.

KEEP OFF EQUIPMENT UNLESS SEAT OR PLATFORM FOR OPERATION AND OBSERVATION IS PROVIDED. KEEP ALL
OTHERS OFF.

PTO SHIELD MUST ROTATE FREELY AND BE IN PLACE.

ALWAYS RUN PTO STRAIGHT IN LINE TO AVOID AN ACCIDENT BY BREAKAGE.

YOU MUST OBSERVE ALL APPLICABLE TRAFFIC LAWS WHEN TRANSPORTING ON PUBLIC ROADWAYS (WHERE
LEGAL TO DO SO). CHECK LOCAL LAWS FOR ALL HIGHWAY LIGHTING AND MARKING REQUIREMENTS AND
COMPLY WITH THESE LAWS.

MAKE CERTAIN EVERYONE IS CLEAR OF MACHINE BEFORE STARTING ENGINE OR OPERATION.

PLEASE KEEP ALL DECALS AND SLOW MOVING VEHICLE SIGN CLEAN SO THEY ARE LEGIBLE.

Read the 

HEADS UP Rules before you operate our equipment.

 

DO NOT allow persons other than the authorized adult operator near the machine.

 

DO NOT clean, adjust, or lubricate the machine when any part is in operation.

 

DO NOT pass in front of discharge area of machine when implement is in operation.

 

Tractor PTO MUST match implement PTO. (NEVER USE PTO ADAPTERS.)

This safety alert symbol           means ATTENTION! BE CAREFUL! YOUR SAFETY IS INVOLVED! It stresses an attitude 
of HEADS UP FOR SAFETY,  also read all other decals as they are also safety warnings. 

Содержание V-FORCE 7400 Series

























































































Отзывы:

Нет отзывов