Metsys RS2-RG Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 14

Metsys RS2-RG Скачать руководство пользователя страница 12

10 I

P R O D U C T S P E C I F I C A T I O N S

Note:

Appearance and specifications may differ due to product improvement.

Working distance varies depending on the operating environment. Battery life
depends on battery capacity and quality, it is recommended to use a large
capacity battery.

B A T T E R Y

Change the battery if is displayed .
Open the battery compartment by unlatching the battery door [12].
Remove the battery and insert a new one (observe correct polarity!).
Dispose of the used battery (see chapter on environmental
protection).

Inserting / changing the battery

FEATURE

Capture Height
Numeric Readout Height
Reception Angle
Detectable Spectrum
Working Radius

Accuracy (Dead band)
Beeper Volumes
- High
- Low
Automatic Shutoff
Filter Against

Marking Notch
Physical Dimensions
Weight without clamp
Protection Class
Power Supply
Battery Life
Operating Temperature
Storage Temperature

SPEC'S

90mm
80mm
± 45°
450nm to 800nm
300m (depending
on laser transmitter)
See page 2. Table

> 100 dBA
> 75 dBA / off
After 30 min
Flash / sunlight /
LED / fluorescent
lamp
41 mm / Top edge
135 x 69 x 25 (mm)
0.19 KG
IP 67 (waterproof)
1 x AA battery
> 45h
-10°C to +50°C
-40°C to +70°C

«
...
10
11
12
13
14
»

Содержание RS2-RG















Отзывы:

Нет отзывов