Metso NELES NDX 511 Series Скачать руководство пользователя страница 53

Страница: 53 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

13.4

Using DTM

This section introduces standard DTM functions and

explains how to perform them efficiently. Note that after

installing DTM, you must update DTM Catalog in the frame

application before you can use the DTM.

13.4.1

DTM settings

Metso DTM setup package installs an additional utility, which

provides global DTM configuration options. It allows chang

ing DTM language and save data folder. The configurator util

ity can be started from Start menu

→

All Programs

→

Metso

Device DTM

→

Metso NDX DTM

→

NDX DTM Configurator.

Fig. 52

13.4.2

Frame application functions

Here is an example of a FDT frame application menu struc

ture, which provides access to different DTM functions:

Fig. 53

The example is showing, where Import/Export functionality

can be found and how to access Offline/Online parame

terization and Diagnosis functionality.

13.4.3

Import/Export

The Export function of DTM allows you to save device con

figurations on your computer or local computer network

for later use or as a backup file. The Import function allows

you to load previously saved configurations into the DTM

for use in device configuration. Exported configurations

are saved in .xml file format.

Location of the Import and Export functions depends on

the FDT frame application used. Usually there is a menu

(or contextmenu with right mouse click), which provides a

set of standard actions, for example “Online Parameterize”.

In this same menu should be a section called “Additional

Functions”. Under the Additional Functions menu are the

Import and Export functions.

13.4.4

Printing

Printable report from a device via a DTM instance is available

through the frame application functions.

13.5

NDX DTM

Metso DTM provides three different user interfaces, each

for very distinct purpose:

1. Parameterize Offline window

2. Parameterize Online window

3. Diagnosis window

These views are available from the FDT frame application

menu structure.

13.5.1

Parameterize Offline

Fig. 54

Following DTM views are available when device is in offline

mode:

Device Information

Status Configuration

All Parameters

Please see the chapter Parameterize Online for detailed

information on each view.

13 DEVICE TYPE MANAGER (DTM)

OPER

ATION

Содержание NELES NDX 511 Series

























































































Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды

Metso NELES NDX 511 Series, Инструкция по установке, обслуживанию и эксплуатации

Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды