manualshive.com logo in svg

Metrohm 2.942.0500, Руководство пользователя, Страница: 41 / 63

Поделиться
Скачать
Metrohm 2.942.0500 Скачать руководство пользователя страница 41

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭

3 Installation

942 Extension Module Vario SeS/PP (2.942.0500)

￭￭￭￭￭￭￭￭

33

 

4 Putting the adsorption cartridge holder into the instrument

￭

Place the adsorption cartridge holder with the CO

2

 adsorption car-

tridge CW into the instrument's detector chamber.

3.7 

Connecting an Extension Module

CAUTION

The 940 Professional IC Vario 

has to be switched off

 when connect-

ing the Extension Module!

Accessories

For this step you need the following accessories:

￭

6.2156.060 cable Extension Module - Professional IC, 40 cm
or

￭

6.2456.070 cable Extension Module - Professional IC, 1 m (optional
accessory)

The connection sockets are located on the rear of the instrument.

Connecting the Extension Module to the IC instrument

 

1

Plug the connecting cable (6.2156.060) into the 

In

 connection

socket on the Extension Module and tighten it in place.

 

2

Plug the other end of the connecting cable into the 

Extension

Module

 connection socket on the IC instrument and tighten it in

place.

Содержание 2.942.0500
































































Отзывы:

Нет отзывов