background image

  

 

M2 

 

Page 4 

 

The manufacturer is not responsible for mistakes that could be found in this 
handbook and also for direct or indirect damage resulting from the equipment, its 
performances and the use of this product. 
 

CLEANING

 

 
Use a soft cotton cloth slightly soaked with an ethyl alcohol based product. 

DO NOT USE

 the following products: acetone, benzene, toluene and halogens 

hydrocarbons. 
 

3.

 

INTRODUCTION 

 

3.1.   PRODUCT PRESENTATION 

 
The M2 digital readout allows dimensional control using 1 or 2 probes. 
It is possible to make simple measurement (with one probe), or combined 
measurement (with 2 probes) : sums or differences  
Measurements are made in comparison with a reference part: the master. 
The M2 can be connected to a PC thanks to its RS232 connection. 
A footswitch can be connected in order to transfer measurements. 
 

3.2.  PROBES 

 
The following probes can be connected : 
 

Heidenhain Specto TTL

 : measuring range 12 and 30mm, resolution 0.5µm 

or 1µm 

Heidenhain MT TTL

 : measuring range 12 and 25mm, resolution 0.1µm 

 (1) Mitutoyo LG series

, measuring range 10 to 50mm, resolution from 0.1 to 

1µm 

 
(1) Needs an adaptor for the connection. 

3.3.   CHARACTERISTICS 

 

  TFT colour display 4,3’’, resolution 480x272. 

 Static measurements 

  Analogue or digital display 

  2 measurement configurations (2 characteristics) 

  Possibility to select automatically the characteristic by moving a probe or by 

pressing a key. 

  Relative or absolute display by pressing a key 

  Measuring direction inversion by pressing a key 

  Display resolution (from 1 to 5 decimals) 

  Metric or Imperial (Inches) measurement 

  RS232 port for communication with a PC 

  Measurement transfer by pressing a key, footswitch input or retro-command on 

the RS232 port. 

  Temporary measurements stop. 

Содержание M2

















Отзывы: