background image

12    

7351J Very Intelligent Early Warning (VIEW) Laser Smoke Detector Technical Bulletin

RF Shield

lpx751_2

Chamber Cover

Cover Removal

 Tabs

Circuit Board

Photo Diode

Detector Cover

Smoke Sensing

Chamber Cover/Screen

Smoke Sensing

Chamber Base

Spring Contact
To Bug Screen

Smoke Detector

Base

Contacts to

Mounting Brackets

Figure 4: Screen Assembly and Sensing Chamber

This smoke detector does not produce any hazardous laser radiation. It is
certified as a Class 1 laser product under the United States Department of
Health and Human Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968.

The radiation emitted inside the smoke detector is completely within the
protective housings and external covers. The laser beam cannot escape
from the detector during any phase of operation.

The Center of Devices and Radiological Health (CDRH) of the
United States Food and Drug Administration implemented regulations for
laser products on August 2, 1976. These regulations apply to laser
products manufactured after August 1, 1976. Compliance is mandatory for
products marketed in the United States.

Laser Safety
Information

Содержание 7351J














Отзывы: