Metabo SPA 2002, Оригинальное руководство пользователя

Страница: 8 / 80

ENGLISH en
8
Original instructions
We, being solely responsible, hereby declare: this
chip extraction system identified by their type and
serial number *1) conform to all relevant provisions
of the directives *2) and standards *3). Technical
documents for *4) - see page 2.
This device is not designed for the use of persons
(including children) with limited physical, sensory
or mental aptitude or lack of experience and/or
knowledge.
Unauthorised modifications to the device and the
use of parts that are not tested and approved by
the manufacturer are prohibited.
All improper use of the device is regarded as non-
specified use; this can result in unpredictable
damage! The user bears sole responsibility for any
damage caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
2.1 The chip extraction system is
- suitable for the extraction and separation of dry
wood dust and chips of dust explosion classes St
1 (KST value ≤ 200 bar m/s);
- not suitable for dust with KST value > 200 bar m/
s (dust explosion class St 2 and St 3, and/or with
minimum ignition energy below 10 mJ
- not suitable for extraction of explosive or similar
substances, for explosive gaseous
atmospheres, for flammable liquids and for
mixtures of flammable dust and liquids
- not suitable for use in potentially explosive
atmosphere
- not suitable for extraction from machines with an
increased risk of generating ignition sources
(note: according to BGI 739-1 these are
shredding machines, multi-blade circular saws
and wide-belt sanding machines in the
manufacture of chipboards, doors, strips and
parquet)
WARNING
This system is not intended for the extraction
of materials other than those specified as suitable,
hot or aggressive dust, lubricating oils etc.
Coarse pieces of wood, metals etc. must not be
extracted on a large scale due to the mechanical
overload of the housing components.
- The system is tested in accordance with the GS-
HO-07 test principles of the
Prüf- und Zertifizierungsstelle Holz im
Fachbereich Holz und Metall
Vollmoellerstraße 11
70563 Stuttgart
. It is therefore suitable for separating wood dust,
where the residual dust content level 3 "H3" of 0.1
mg/m3 is reliably observed. It bears the mark of
conformity with the corresponding supplement:
- The system is suitable for collecting, conveying
and separating wood dust and wood chips from
individual dust sources.
The result of the dust test is based on the
extraction of dry wood dust and dry wood chips
with a residual moisture content < 30%.
Information with regard to changing
applications
The system can be used to extract chips and dust
from processing machines that have a maximum
connection diameter for the cross section of the
chip extraction system:
connecting piece Ø 100 mm = 0.00785 m
2
A1 = tube cross section dust source 1
A2 = tube cross section dust source 2
A3 = tube cross section clean air dust extractor
A1 + A2 < A3
(see fig. D)
If extraction of contaminated air is required at
several points of a processing machine (e.g.
bench-mounted circular saw with two extractor
connections), make sure that the sum of the cross
sections from the machine extractor connection
pieces is less than the cross section on the system.
The gradation and design must be selected so that
the flow speeds remain approximately the same.
Caution !
Extraction on wood processing machines with a
suction nozzle diameter greater than 100 mm is
not permitted.
For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Read the operating
instructions to reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in electric
shock, fire and/or serious injury.
Keep all safety instructions and information
for future reference.
Always include these documents when passing on
your power tool.
Observe these points to avoid injury, fire and other
hazards due to improper use and operation of the
system.
Warning !
Assembly, electrical connection, supply
connection, maintenance, commissioning, repair
etc. may only be carried out by trained specialist
personnel.
The chip extraction system may only be operated
with completely closed inspection doors and
covers!
Before carrying out any work on the system or
opening the inspection doors, it must be ensured
that the power supply is switched off (on all poles),
the mains plug is disconnected and secured
against unauthorised reconnection!
The system must be properly installed and used in
accordance with our instructions.
If assembly is carried out contrary to our
regulations and if there is a causal link between the
defect / damage and improper modifications,
processing or other treatment, all claims for
damages or warranty are excluded. The customer
must provide evidence that the improper
installation was not the cause of the defect that
occurred.
General maintenance instructions in the operating
and installation instructions for the system must be
observed.
The design and construction of the system comply
with the standards listed in the Declaration of
Conformity in order to minimize and potential
hazards arising from the system.
It must be ensured that all persons commissioned
to deal with the system have read, understood and
observed these operating instructions in their
entirety!
In order to avoid dangers within the company, all
factory instructions, operating and work
instructions of the user apply in addition to these
operating instructions.
Personal protective equipment is required for work
on the system!
- Dust masks when changing the filter and when
disposing of the collected materials. Gloves for
filter change and assembly work.
- The machine should only be used in dry and
frost-free areas. Consult the manufacturer in the
event of deviations.
- The system may be operated at room
temperatures b 5° to + 40° C.
- Make sure that the power cable is not damaged
by being driving over, crushed, dragged or
similar.
- The power cable must be inspected regularly for
signs of damage or ageing.
- The machine may only be used if the power cable
is not damaged.
- When replacing the power cable, only the cable
type stated in the specifications may be used.
- When replacing the power plug, use only the plug
type stated in the specifications.
- The power cable and mains plug should only be
replaced by qualified personnel.
- If the mains or machine power cable needs to be
replaced, it must not be deviated from the details
specified by the manufacturer.
- The power plug of the system may only be
plugged in after installation on site.
- Connection to CEE plug (e.g. wall socket) with 3
x 16 A backup fuse or 1 x 10 A single-phase
alternating current.
- Disconnect the mains plug after use, prior to
moving the chip extraction system to another
location and before cleaning, maintaining,
replacing or removing movable parts.
- The use of electric coupling devices and
adapters is not permitted during operation.
- Pay attention to the motor’s direction of rotation.
Warning !
In the event of fire, the device must be
disconnected from the mains by pulling the power
plug. Do not open the device, there could still be
glowing embers. Alert the fire brigade that will
open the device under protection. Do not activate
filter cleaning! Risk of fire and injury.
Caution!
To protect any released pollutants, the rooms may
only be entered with respiratory masks.
For devices built without ignition sources applies:
- They are not suitable for extracting objects (from
processing machines) where active ignition
sources cannot be ruled out.
- From a safety viewpoint, dust-explosion
protected industrial vacuum cleaners and pure
air dust extractor are unsuitable for vacuuming or
extracting materials that pose a danger of
explosion or similar based on § 1 Explosive G,
dust of dust-explosion class St 2 and St 3,
flammable liquids and mixtures of flammable
dust with flammable liquids.
- Only plug connections in accordance with VDE
0165 section 6.6.1 may be used for the
connection of electrically operated industrial
vacuum cleaners and chip extraction systems.
Coupling connectors and adapters are not
permitted. The dust-collection container must be
emptied when necessary. Only original
replacement parts should be used.
- Fluids, aggressive gases, easily flammable
materials or glowing particles (glowing embers or
similar) should not be extracted. It is prohibited to
use the dust extractor e.g. in paintshops.
Extraction at wood-processing machines where
active ignition sparks and glowing embers are
expected (e.g. multiple-bladed saws) is
prohibited.
- Only clean the housing with household
detergents and a damp cloth.
- These extraction unit are not intended for
installation in an ex-area.
Unplug the power plug from the outlet to
disconnect it from the power supply, before
effecting any work!
Disconnect the power supply plug in the event of
an emergency stop.
4.1 General
The chip extraction system may only be operated
on TN networks with grounded neutral.
1. Declaration of Conformity
2. Specified use
3. General safety information
4. Special safety instructions