MERRICK MC3 35.00.EX Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 69

MERRICK MC3 35.00.EX Скачать руководство пользователя страница 53

this screen shot means that this procedure has never been executed since the last time
the controller was subject to a RAM Reset procedure.

Weight Procedure

The Weight Procedure is used to calibrate the scale to show a correct net weight.

To run this procedure, you will need calibration weights that represent at least 20% of the

Design Weight

. The weight in the hopper plus the sum of the calibration weights may not

exceed the

Hi Weight

limit. The procedure will first sample the current weight, and then

the weight with the calibration weights added.

To begin the Weight Procedure push the

Start

button.

If the total weight (weight in the hopper plus calibration weights) exceeds the

Hi Weight

limit, the display will show an Overload Condition screen.

Normally, the start weight is sampled. This requires that the weight value is stable.

In the next screen, the sampled weight before applying the calibration weighs is
displayed (

Test Zero

), along with the expected calibration weight. By pushing the Change

Value button, you can alter the Calibration Weight value.

Push the OK button and load the calibration weights onto the hopper.

35.00.EX O&M Manual

49

«
...
51
52
53
54
55
...
»

Содержание MC3 35.00.EX






































































Отзывы:

Нет отзывов