1
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is NOT connected BEFORE installing the receiver.
To prevent possible SERIOUS INJURY or DEATH from a moving residential gate,
residential garage door or a commercial door:
R
E
V
E
N
.
n
e
r
d
li
h
c
f
o
h
c
a
e
r
f
o
t
u
o
sl
o
rt
n
o
c
e
t
o
m
e
r
p
e
e
k
S
Y
A
W
L
A
•
permit children to operate, or play with remote control transmitters.
y
lr
e
p
o
r
p
si
,
yl
r
a
e
lc
n
e
e
s
e
b
n
a
c
t
i
n
e
h
w
Y
L
N
O
r
o
o
d
r
o
e
t
a
g
e
t
a
vi
t
c
A
•
adjusted, and there are no obstructions to door travel.
ALWAYS keep residential gate, residential garage door or commercial door in
sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
•
To prevent possible SERIOUS INJURY or DEATH, the use of
CONSTANT OPERATION on residential openers is PROHIBITED.
When a receiver is used to activate a commercial door opener, a
reversing edge MUST be installed on the bottom of the door. Failure to
install a reversing edge under these circumstances may result in
SERIOUS INJURY or DEATH to persons trapped beneath the door.
COMMERCIAL ACCESS CONTROL RECEIVER
MODEL STAR1000EVO
Control
Station
Receiver Without
Faceplate
Single Operator
9 - 30 volts AC/DC
250 mA max
Power
(not provided)
Supply
APPLICATION
The STAR1000EVO is a high capacity single channel commercial access
control receiver for commercial door openers,
and dry contact triggered
devices. The STAR1000EVO is compatible with Security 2.0™ remote
+
controls and wireless keyless entries. The receiver capacity is 1,000
devices and can be any combination of remote controls and wireless
keyless entries. The receiver is watertight according to IPX44
specification.
INSTALLATION
ener to be controlled by the
p
o
e
h
t
r
a
e
n
n
o
it
a
c
o
l
t
n
e
i
n
e
v
n
o
c
a
t
c
e
l
e
S
.
1
receiver within “line of sight” of the intended transmitting location.
E:
T
O
N
Do not mount LCD screen in direct sunlight. Avoid mounting
the receiver in a metal enclosure or near other wireless receiving or
transmitting devices.
e
r
a
w
d
r
a
h
e
t
a
ir
p
o
r
p
p
a
h
ti
w
e
c
a
fr
u
s
d
e
ri
s
e
d
e
h
t
o
t
t
e
k
c
a
r
b
e
h
t
t
n
u
o
M
.
2
(not provided) (Figure 1).
e
h
t
e
v
o
m
e
r
d
n
a
r
e
v
i
e
c
e
r
e
h
t
f
o
k
c
a
b
e
h
t
n
o
s
w
e
r
c
s
)
8
#
(
4
e
h
t
e
v
o
m
e
R
.
3
faceplate. Unplug the keypad connector from the control board.
:
E
T
O
N
Be careful not to damage the keypad cable while removing the
faceplate.
l
a
i
c
r
e
m
m
o
c
r
o
e
t
a
g
r
u
o
y
o
t
r
e
f
e
R
.
)
2
e
r
u
g
i
F
(
s
n
o
it
c
e
n
n
o
c
g
n
ir
i
w
e
k
a
M
.
4
door opener owner’s manual for more specific information.
5. Reconnect the keypad connector to the board (labeled J9).
6. Secure the faceplate with the 4 (#8) screws previously removed.
7. Install the antenna provided.
:
E
T
O
N
Use the optional ANT4X-1LM antenna extension kit
(see page 4) to mount the remote antenna as high and far from
metallic objects as possible for best radio range.
e 2
h
t
h
ti
w
e
r
u
c
e
s
d
n
a
t
e
k
c
a
r
b
g
n
it
n
u
o
m
e
h
t
o
t
n
o
r
e
v
i
e
c
e
r
e
h
t
p
a
n
S
.
8
(#8) screws provided.
9. Tighten the watertight connector to secure and seal the wiring.
Figure 1
Mounting Bracket
Watertight Connector
Keypad Connector
Antenna
Connector
Figure 2
Backup Memory
Module
Relay
Connection
Power
Connection
