Merlin CYCLONE PRO MT120EVO страница 4 Скачать руководство пользователя

Страница: 4 / 24

IMPORTANTSAFETYinformation

TALLATIONBEFOREREADINGTHOROUGHLY

N2966

Owners Copy: SAVE THESE INSTRUCTIONS for future reference

MT120EVO

Sectional Garage Door Opener

Installation and Operating Instructions

This manual contains IMPORTANT SAFETY information

DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY

N2966

gomerlin.com.au
gomerlin.co.nz

114A3361

For Service Call

Installation Date

132A2900

RISK OF ENTRAPMENT

Repeat Safety Reverse Test monthly Door

must reverse on contact with a 40mm obstacle

placed on the floor Make necessary adjustments
AUTOMATIC DRIVE:

Keep away from the area of the door since it may

operate unexpectedly
EMERGENCY RELEASE:

To release pull down firmly on the red handle

CARTON INVENTORY

(1) Opener

(2) Hand held transmitter (2)

(3) Wireless wall control

(4) Curved door arm

(5) Hanging bracket (2)

(6) Rail bracket

(7) Header bracket

(8) Door bracket

(9) Hardware bag

(10) Rail assembly (separate carton)

(11) C-Rail bracket (2)

(12) Warning labels

(13) Manual

(14) Centre rail brackets (set)

(15) Door bracket

Your garage door opener and rail are packed in two seperate cartons. The CyclonePro (MT120EVO) opener carton

contains the opener, its fitting hardware and accessories. The rail carton contains the rail and some hardware.

RAIL SIZES AVAILABLE

DOOR HEIGHT:
Sectional Doors

CHAIN & RAIL
PART NUMBER:

RAIL LENGTH:

CEILING FIXING
POINTS: (standard)

ALTERNATE
FIXING POINT:

Up to 2.4 m

7024 CR5ANZ

3200 mm single piece

3040 mm

3150 mm

From 2.4 - 3.4 m

740 CR5ANZ

1000 mm extension

4040 mm

4150 mm

NOTE:

The Ceiling Fixing Point (Standard) is the position of the hanging bracket measured back from the lintel (see

item 1 to 7 of “completed installation”). Also allow 400 mm back from the fixing point for installation of the powerhead

(item 7 to 9 of “completed installation”).

The Alternate Fixing Point will position the hanging bracket between the Powerhead C-Rail brackets, (Item 14 of

“completed installation”) and may line up with a structural support more favourably.

Содержание CYCLONE PRO MT120EVO

























Результаты поиска

Содержание CYCLONE PRO MT120EVO

Отзывы:

Похожие инструкции для CYCLONE PRO MT120EVO

Бренды по названию

Популярные бренды

Merlin CYCLONE PRO MT120EVO, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CYCLONE PRO MT120EVO

Отзывы:

Похожие инструкции для CYCLONE PRO MT120EVO

Бренды по названию

Популярные бренды