manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 97

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22

Page 95

Printed in USA

10     Troubleshooting

Front Axle Declutch Does Not Engage/Disengage Diagnostics

Return the vehicle 
to service.

Return the vehicle 
to service.

Return the vehicle 
to service.

Turn wheels left and right several

times, then try to shift declutch.

Check indicator light,
and engagement and
disengagement sensors
for correct operation.

Check the available air
pressure. The transfer
case requires at least 
60 psi (4.14 bar) at all
times to operate correctly.

Yes

Yes

Yes

Yes

Yes

No

No

No

No

Replace faulty indicator
light or sensor, then
try to shift declutch.

Correct system air pressure.
Refer to OEM instructions. 

Check the piston cylinder on the declutch.
Clean the air supply system. 
Refer to OEM instructions. 
Verify the transfer case shifts correctly. 

Return the vehicle to service.

Check the PTO for leaks. 

Reinstall the transfer case onto the 
vehicle. Road test the vehicle to
confirm the problem is corrected.

No

Remove the transfer case from the vehicle.
Follow disassembly procedures.  
Inspect the front axle drive gear, shaft, shift 
collar, collar engagement teeth on gear, shift 
fork, shift fork bore, piston, o-ring, and return 
spring for damage. 
Repair all damaged components.

Reassemble the transfer case.
Verify the transfer case shifts correctly.

Return the vehicle 
to service.

Light or 

sensor 
faulty?

Air 

pressure 65 psi

(4.48 bar) or

more?

Declutch 

shifts 

correctly? 

Declutch 

shifts 

correctly? 

Air 

system

contaminated?

4001529d

Figure 10.5 

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды