Meritor MM-0861 Скачать руководство пользователя страница 95

Страница: 95 / 118

MM-0861 / Revised 06-22

Page 93

Printed in USA

10 Troubleshooting

Excessive Noise and Vibration Diagnostics

Determine all driveline angles.
Angles should not exceed 5º and the
difference between any of the angles
should not be greater than 1.5º.

Excessive driveline angles are
the leading cause of drivetrain
vibration and noise.
Consult the vehicle manufacturer.

Check transfer case
mounting fasteners for
correct torque. Refer to
vehicle manufacturer’s
specifications.

Check all drivelines for
adequate balancing.

Replace or
rebalance
driveline.

Check u-joints for
excessive wear and
damaged rollers.

Check for loose or broken
case-to-vehicle mounting
brackets and fasteners.

Return the
vehicle to service.

Road test the
vehicle to
determine if
noise/vibration
is still present.

Replace broken
brackets and/or
tighten all
fasteners to
specified torque.

Yes

Replace worn bearings
or damaged components.

Check all declutch and all
transfer case shafts for
excessive wear. Repair as
necessary.

Problem

corrected?

Loose

fasteners or

broken

bracket?

Are angles

excessive?

Wear or

damage?

Balanced?

4001527b

Figure 10.3

Содержание MM-0861























































































































Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды

Meritor MM-0861, Руководство по обслуживанию

Результаты поиска

Содержание MM-0861

Отзывы:

Бренды по названию

Популярные бренды