manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 104

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22
Page 102

Printed in USA

11     Lubrication and Maintenance

Table G: Transfer Case Oil Specifications

Oil Description 

1 2

Full-Synthetic 

Oil 

3

A.P.I. GL-5 

(Axle Lube) 

4

Meritor 

Specification

O-81

DO NOT USE IN 

TRANSFER CASES

A.P.I.  

Specification

— 

Military 

Specification

SAE J2360

SAE Grade

40W

Outside 

Temperature

Above -40

º

F 

(-40

º

C)

1 Do not mix or switch oil types. Use the same oil that initially filled 
the transfer case.

2 Do not use multi-viscosity oils.

3 Meritor-approved full-synthetic oil for Meritor manual 
transmissions is also approved for Meritor transfer cases. Use 
synthetic oil only if the transfer case was initially filled with 
synthetic oil.

4 Do not use multi-viscosity (i.e., 80/90W) GL-5 Gear Oil, axle lube.

•  Do not mix or switch oil types. Use the same oil that initially 

filled the transfer case. Use synthetic oil only if the transfer 
case was initially filled with synthetic oil.

•  Any Meritor-approved full synthetic oil for Meritor manual 

transmissions is also approved for Meritor transfer cases. 

 CAUTION

Transfer case input speed requirements apply. Damage to the 
transfer case can occur if TP-9441 requirements are not followed.

 CAUTION

Transfer case oil fill volumes do not include additional oil needed 
to fill the OEM oil cooler and lines. The transfer case oil fill 
volumes listed below are for reference only. Fill to the bottom of 
the oil fill hole for proper oil level. 

Table H: Transfer Case Oil Fill Volumes*

Model

Pints (Liters)

MTC-4208X

13.25 (6.27)

MTC-4208XLEC

13.50 (6.39)

MTC-4208XLEV

12.50 (5.92)

MTC-4208XP

13.25 (6.27)

MTC-4210X

13.25 (6.27)

MTC-4210XLEC

13.50 (6.39)

MTC-4210XLEV

12.50 (5.92)

MTC-4210XP

13.25 (6.27)

MTC-4213

13.25 (6.27)

*All oil cooler equipped transfer cases will use additional oil to 
compensate for the cooler and cooler lines. OEM’s and vehicle 
operators must ensure during oil level check and adjustment 
additional oil is added. See procedure to in this section to check 
and adjust the oil level for cooler equipped transfer cases.

Table I: Transfer Case Seals and Drivers

Model

Seal Position

Seal Service 
Part Number

Previous Seal 
Part Number

Seal Driver Sleeve 

Driver

MTC-4208, MTC-4210,  
and MTC-4213

Input Shaft

A1-1205X2728

A 1205R2592

2728T1

2728T1

MTC-4208 and MTC-4210

Forward and Rear Output R945007

A 1205R2592

KIT 4454

NA

MTC-4213

Forward Output

R945007

A 1205R2592

KIT 4454

NA

Rear Output

R945010

A 1205Q2591

KIT 4454

NA

MTC-4208 and MTC-4210

PTO Seal

R945008

A 1205P2590

KIT 4454

NA

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды