manualshive.com logo in svg

Meritor MM-0861, Руководство по обслуживанию

Поделиться
Скачать
Meritor MM-0861 Скачать руководство пользователя страница 101

Copyright Meritor, Inc., 2022

MM-0861  /  Revised 06-22

Page 99

Printed in USA

11    Lubrication and Maintenance

MTC-4208X/XP, MTC-4210X/XP, AND MTC-4213X

4006338f

OIL COOLER READY

INLET

TUBE

FITTINGS

DRAIN

PLUG

FILL

PLUG

FRONT VIEW

FRONT INPUT

YOKE

FRONT

OUTPUT

YOKE

Figure 11.4 

 CAUTION

Only install the Meritor multi-lip unidirectional seal at the input 
position from the transmission in an MTC-4208, MTC-4210, or 
MTC-4213 Series transfer case. If the multi-lip seal is installed in 
either the rear output position or forward output position on these 
transfer cases, loss of lubricant and damage to components can 
occur.

The multiple-lip seal must be serviced with the seal and sleeve. 
The service part number provides both when required. Check the 
application carefully before installing the multiple-lip seal.

Oil Fill Procedure

 CAUTION

Only use new lubricant when changing or adjusting the oil in the 
transfer case. NEVER reuse lubricant, which can contain metallic 
particles and other contaminants. Damage to components can 
result.

 CAUTION

Meritor does not approve petroleum-based and multi-viscosity oil. 
NEVER install API GL-5 oils, which contain extreme-pressure (EP) 
additives. These additives can form sludge at normal operating 
temperatures. Damage to components can result. Use only SAE 
Grade full-synthetic 40W or 50W oil, Meritor specification O-81, 
in the transfer case.

 CAUTION

When servicing the transfer case, add the specified lubricant until 
the oil level is even with the bottom of the fill hole. NEVER overfill 
the transfer case, which can cause the transfer case to overheat. 
Damage to components can result.

 CAUTION

NEVER operate the transfer case if the oil level is below the bottom 
of the fill hole, which may be an indication that the transfer case is 
leaking. Damage to components can result. If the transfer case is 
leaking, repair the leak. Adjust the oil level before returning the 
transfer case to service.

NOTE: 

Meritor recommends the oil cooler lines should be routed 

to prevent oil flow back into the transfer case sump. This can be 
accomplished by routing lines with a P-trap configuration for both 
the oil cooler inlet and outlet lines. Failure to do so may result 
in the oil draining back in to the transfer case sump, giving the 
appearance of an over filled transfer case when checking and 
adjusting the oil level.

ALTERNATE FILL LOCATION /

BREATHER

OIL FILL

OIL

DRAIN

MAGNETIC

PLUGS

4018584a

Figure 11.5 

Содержание MM-0861























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды