Mercury Sterndrive QSD 2.0 Скачать руководство пользователя страница 47

Страница: 47 / 131

Section 4 - Specifications

90-8M0069751

eng

APRIL 2012

Page 39

Engines with Seawater System Oil Cooler

QSD 2.0

System Capacity

Fluid Type

Part Number

Engine oil (with filter)

6.00 L (6.30 US qt)

15W40 4‑cycle Diesel Engine Oil

92‑877695K1

Closed‑cooling system

7.50 L (8.00 US qt)

Marine Engine Coolant

(Only available in Europe)

92‑813054A2

Fleetguard Compleat with DCA4

Fleetguard Part Number: CC2825

Container size: 3.75 L (1.00 US gal)

Obtain locally

Alpha Sterndrive Fluid Specifications

NOTE: Oil capacity includes gear lube monitor.

Model

Capacity

Fluid Type

Fluid Part Number

Alpha One

1892 ml (64 oz)

High Performance Gear

Lubricant

92‑858064K01

Bravo Sterndrive Fluid Specifications—Diesel

Sterndrive Model

Fluid Capacity includes the

Sterndrive and the

Gearlube Monitor

Fluid Type

Fluid Part Number

Bravo One X Diesel

Bravo One XR

2736 ml (92‑1/2 oz.)

High Performance Gear

Lubricant

92‑802854A1

Bravo Two X Diesel

3209 ml (108‑1/2 oz.)

Bravo Three X Diesel

Bravo Three XR

2972 ml (100‑1/2 oz.)

Approved Power‑assisted Steering Fluids

Standard Applications

Description

Part Number

Power Trim and Steering Fluid

92‑858074K01

Dexron III Automatic Transmission Fluid (ATF)

Axius Applications Only

Description

Part Number

Power–Assisted Steering Fluid

Dexron III ATF

Approved Power Trim Fluids

All Applications

Description

Part Number

Power Trim and Steering Fluid

92‑858074K01

SAE Engine Oil 10W‑30

Obtain locally

SAE Engine Oil 10W‑40

Approved Paints

Description

Part Number

Marine Cloud White

8M0071082

Mercury Light Gray Primer

92‑80287852

Содержание Sterndrive QSD 2.0




































































































































Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды

Mercury Sterndrive QSD 2.0, Руководство пользователя

Результаты поиска

Содержание Sterndrive QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды