Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя | Manualshive

Страница: 87 / 170

background image

Section 5 - Maintenance

90-8M0050539

eng

MAY 2011

Page 79

Engine Oil—350/377 MAG ECT and SeaCore 350/377 MAG ECT

Checking

NOTICE

Discharge of oil, coolant, or other engine/drive fluids into the environment is restricted by law. Use caution not to spill oil, coolant,

or other fluids into the environment when using or servicing your boat. Be aware of the local restrictions governing the disposal

or recycling of waste, and contain and dispose of fluids as required.

1. Stop the engine. Allow approximately five minutes for the oil to drain into the oil pan. The boat must be at rest in the water.
2. Remove the dipstick. Wipe clean and reinstall fully into the dipstick tube. Wait 60 seconds to allow trapped air to vent.

NOTE: Ensure that dipstick is installed with oil level indication marks facing the rear of the engine (flywheel end).

33200

Dipstick

IMPORTANT: Add the specified engine oil to bring the level up to, but not over, the full or OK range mark on the dipstick.

3. Remove the dipstick and observe the oil level. Oil level must be between full or OK range and add. Reinstall dipstick into

dipstick tube.

Filling

IMPORTANT: Do not overfill the engine with oil.

IMPORTANT: Always use the dipstick to determine the exact quantity of oil or fluid required.
1. Remove oil fill cap.

33210

Oil fill cap

2. Add the specified engine oil to bring the level up to, but not over, the full or OK range mark on the dipstick. Recheck oil level.
3. Replace the fill cap.

«
...
85
86
87
88
89
...
»

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренд: Festo Страницы: 76

Бренд: Hatz Diesel Страницы: 48

Бренд: DELTA DORE Страницы: 16

Бренд: Petter Страницы: 58

Бренд: DoorHan Страницы: 16

Бренд: Doosan Страницы: 179

dunkermotoren D258

Бренд: Ametek Страницы: 8

Kohler KDI 1903TCR-MP

Бренд: LOMBARDINI MARINE Страницы: 56

Бренд: Sisu Diesel Страницы: 80

Бренд: Greyhound Страницы: 20

Бренд: Detroit Diesel Страницы: 195

Shire 15 Work Boat YM

Бренд: Barrus Страницы: 44

Бренд: Hydro-Gear Страницы: 24

AQUACRAFT .18 MARINE

Бренд: Hobbico Страницы: 4

Бренд: Briggs & Stratton Страницы: 11

Бренд: Briggs & Stratton Страницы: 28

Бренд: Kesseböhmer Страницы: 12

Бренд: Volkswagen Marine Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды