Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 42 / 170

Section 2 - Getting to Know Your Power Package

Page 34

90-8M0050539

eng

MAY 2011

Zero Effort Features

a -

Shift ever

b -

Throttle lever

c -

Trim/tilt switch

Shift Lever -

Shift functions are controlled by the movement of the shift lever. Shift into reverse by moving the shift lever to its aft

position. Shift into neutral by moving the shift lever to its center position. Shift into forward by moving the shift lever to its forward

position.

Throttle Lever -

Throttle functions are controlled by the movement of the throttle lever. Increase the RPM by moving the throttle

lever forward. Achieve Wide Open Throttle (WOT) by placing the throttle lever in its full forward position. Decrease RPM by moving

the throttle lever back. Achieve minimum RPM (idle) by placing the throttle lever in its full aft position.

Trim/Tilt Switch -

Refer to

Power Trim

Dual Console Control with CAN Trackpad Features and Operation

Dual‑Handle Console Control With CAN Trackpad: Features and Operation

1. Operation of shift and throttle is controlled by the movement of the control handle. Push the control handle forward from neutral

to the first detent for forward gear. Continue pushing the handle forward to increase speed. Pull the control handle back from

neutral to the first detent for reverse gear. Continue pulling the handle back to increase speed.

3417

2. Trim switch (if equipped) ‑ Pressing the trim switch allows the engine to trim up and down.

N E

U T

R A

SYNC

THROTTLE

TROLL

TRANSFER

DOCK

1 LEVER

22132

3. Neutral lights ‑ The neutral lights illuminate when the engine is in neutral gear position. The lights will flash when the engine

is in throttle only mode.

NOTE: Gear position is determined by the position of the shift actuator on the engine, not the position of the control handle.

5656

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды