Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя | Manualshive

Страница: 155 / 170

background image

Section 6 - Storage

90-8M0050539

eng

MAY 2011

Page 147

1. Insert a small wire repeatedly to make sure that vent holes, water drain holes, and passages are unobstructed and open.

Sterndrive Water Drain Holes

a -

Speedometer pitot tube

b -

Trim tab cavity vent hole

c -

Trim tab cavity drain passage

d -

Gear housing water drain hole (1 each ‑ port and starboard)

e -

Gear housing cavity vent hole

f -

Gear housing cavity drain hole

NOTICE

The universal joint bellows may develop a set when stored in a raised or up position, causing the bellows to fail when returned

to service and allowing water to enter the boat. Store the sterndrive in the full down position.

2. Lower the sterndrive unit to the full down/in position.
3. For additional assurance against freezing and rust, after draining, fill the cooling system with propylene glycol mixed to the

manufacturer's recommendation to protect engine to the lowest temperature to which it will be exposed during freezing

temperatures or extended storage

IMPORTANT: Mercury MerCruiser requires that propylene glycol antifreeze, mixed to the manufacturers instructions, be used

in the seawater section of the cooling system for freezing temperatures or extended storage. Make sure that the propylene

glycol antifreeze contains a rust inhibitor and is recommended for use in marine engines. Be certain to follow the propylene

glycol manufacturer's recommendations.

Draining Water From the Gen III Cool Fuel Module

Mercury MerCruiser recommends draining the Gen III Cool Fuel module if it is equipped with a drain plug.
1. Remove the drain plug from the Gen III Cool Fuel module and allow the water to completely drain from the module.
2. Inspect the drain plug and the O‑ring for damage. Replace if needed.
3. Place the O‑ring on the drain plug and install the drain plug in the module drain hole. Tighten the drain plug to finger tight.

a -

Gen III Cool Fuel module

b -

Fuel inline fitting

c -

Drain plug

d -

O‑ring

b

a

d

e

f

c

6146

43648

a

b

c

d

c

«
...
153
154
155
156
157
...
»

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренд: Quectel Страницы: 71

Бренд: J.A.P Страницы: 21

Бренд: Daihatsu Страницы: 196

Бренд: Ibiza Страницы: 3

Бренд: Aerotech Страницы: 59

BAUDOUIN PowerKit 16M33 Series

Бренд: WEICHAI Страницы: 142

Бренд: HOND Страницы: 48

Бренд: Sanshin Страницы: 25

Бренд: KYMCO Страницы: 244

EQP III 300 Series

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 6

Бренд: Toshiba Страницы: 31

EQP Global IEC Series

Бренд: Toshiba Страницы: 34

Бренд: Toshiba Страницы: 286

Бренд: Volvo Penta Страницы: 41

Бренд: O.S. engine Страницы: 15

Бренд: YS Страницы: 2

Бренд: O'Donnell Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды