Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 154 / 170

Section 6 - Storage

Page 146

90-8M0050539

eng

MAY 2011

e. Check valve

a -

Drain plug (if equipped)

3. On models with a seawater pickup pump, remove the two blue drain plugs. If the seawater pickup pump does not have blue

drain plugs, or you are unable to access them, loosen the clamps and remove both hoses.

a -

Hose clamps

b -

Blue drain plugs

4. Crank the engine over slightly with starter motor to purge any water trapped in the seawater pickup pump. Do not allow the

engine to start.

5. After the cooling system has been drained completely, install the drain plugs, reconnect hoses, and tighten all hose clamps

securely.

Draining the Sterndrive

NOTE: This procedure is needed only for salty, brackish, mineral laden, or polluted water applications; and for freezing

temperatures or extended storage.

6131

6145

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды