Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 119 / 170

Section 5 - Maintenance

90-8M0050539

eng

MAY 2011

Page 111

MerCathode System—

Electrode assembly replaces the Anode block. System should be tested to ensure adequate output. The

test should be performed where boat is moored, using Quicksilver Reference Electrode and Test Meter.

Description

Location

Figure

Gearcase anode plate

Mounted on the underside of the lower

gearcase.

20336

Ventilation plate anode

Mounted on the front of the gearcase.

20338

MerCathode System

The MerCathode electrode is mounted

to the underside of the gimbal housing.

The MerCathode controler is mounted

on the engine or on the boat transom.

The controler harness connects to the

electrode harness.

20340

Anode kit (if equipped)

Mounted to the boat transom.

20341

Trim cylinder anodes

Mounted on each of the trim cylinders.

20342

Bearing carrier anode (Bravo One)

Located in front of the propeller,

between the front side of the propeller

and the gear housing.

20343

Propshaft anode (Bravo Three)

Located behind the aft propeller.

20344

Checking the Quicksilver MerCathode System

The MerCathode system should be tested to ensure adequate output. Perform the test where boat is moored, using the reference

electrode and test meter. Contact your authorized Mercury MerCruiser dealer for service and information .

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды