Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя

Страница: 117 / 170

Section 5 - Maintenance

90-8M0050539

eng

MAY 2011

Page 109

Serpentine Drive Belt

WARNING

Inspecting the belts with the engine running may cause serious injury or death. Turn off the engine and remove the ignition key

before adjusting tension or inspecting belts.

With a seawater pump

Without a seawater pump

a -

Idler pulley

b -

Water circulating pump pulley

c -

Crankshaft pulley

d -

Alternator pulley

e -

Seawater pump pulley

f -

Power steering pump pulley

Checking

1. Inspect the drive belt for proper tension and for the following:

•

Excessive wear

•

Cracks

NOTE: Minor, transverse cracks (across the belt width) may be acceptable. Longitudinal cracks (in the direction of belt

length) that join transverse cracks are NOT acceptable.

•

Fraying

•

Glazed surfaces

•

Proper tension ‑ 13 mm (1/2 in.) deflection, with moderate thumb pressure, on the belt at the location that has the longest

distance between two pulleys.

mc75130-1

Replacing Belt and/or Adjusting Tension

IMPORTANT: If a belt is to be reused, it should be installed in the same direction of rotation as before.

NOTE: Belt deflection is to be measured on the belt at the location that has the longest distance between two pulleys.

1. Loosen the 16 mm (5/8 in.) locking nut on the adjustment stud.
2. Turn the adjustment stud and loosen the belt.
3. If a new serpentine drive belt is required, remove the old belt and install a new belt onto the pulleys.

6116

6117

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius SeaCore 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius SeaCore 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренды по названию

Популярные бренды