Mercury MerCruiser Axius SeaCore 350 MAG Скачать руководство пользователя | Manualshive

Страница: 113 / 170

background image

Section 5 - Maintenance

90-8M0050539

eng

MAY 2011

Page 105

IMPORTANT: If reusing tab washer, carefully inspect tabs for cracks or other damage. Replace tab washer if condition is

questionable.

a -

Propeller shaft

b -

Thrust hub

c -

Flo‑Torq II drive hub

d -

Propeller

e -

Drive sleeve

f -

Locking tab washer

g -

Propeller nut

1. Slide thrust hub onto propeller shaft, with stepped side toward propeller hub.
2. Apply a liberal coat of one of the following lubricants to the propeller shaft.

Tube Ref No.

Description

Where Used

Part No.

34

Special Lubricant 101

Propeller shaft

92-802865Q02

94

Anti-Corrosion Grease

Propeller shaft

92-802867Q 1

95

2-4-C Marine Lubricant

with Teflon

Propeller shaft

92-802859A 1

3. Install Flo‑Torq II Drive Hub into propeller.

NOTE: The drive sleeve is tapered and will slide fully into the propeller as the nut is tightened and properly torqued.

4. Align splines and place propeller on propeller shaft.
5. Install drive sleeve and locking tab washer.
6. Install and torque the propeller nut.

Description

Nm

lb‑in.

lb‑ft

Propeller nut (minimum)

75

–

55

IMPORTANT: The propeller torque stated is a minimum torque value. Some special use propellers may have a different

torque value. Use the installation information provided with the propeller to determine if another torque value is appropriate

to your propeller.

7. Bend three tabs on the tab washer down into the grooves in spline washer. After the first use, bend the three tabs straight

and retorque the propeller nut. Bend tabs back down into spline washer. Check propeller at least after 20 hours of operation.

Do not operate with loose propeller.

Bravo Two Propeller Removal

!

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the water with a propeller installed. Before

installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the engine from

starting. Place a block of wood between the propeller blade and the anti‑ventilation plate.

1. Place wood block between propeller blade and anti‑ventilation plate to prevent rotation. Straighten bent tabs on tab washer.
2. Turn propeller shaft nut counterclockwise to remove nut.
3. Slide tab washer, spline washer, propeller and thrust hub off propeller shaft.

a

b

c

d

e

g

6215

f

«
...
111
112
113
114
115
...
»

Содержание MerCruiser Axius SeaCore 350 MAG











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MerCruiser Axius SeaCore 350 MAG

Бренд: M+S Страницы: 6

Бренд: Garmin Страницы: 14

Бренд: Navistar Страницы: 197

Бренд: MTU Страницы: 239

Бренд: Siemens Страницы: 20

Бренд: Siemens Страницы: 26

Бренд: Siemens Страницы: 40

Бренд: Siemens Страницы: 87

Бренд: Siemens Страницы: 96

Бренд: Siemens Страницы: 116

Бренд: Siemens Страницы: 156

Бренд: Siemens Страницы: 252

EQP III 300 Series

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 6

Бренд: Toshiba Страницы: 31

EQP Global IEC Series

Бренд: Toshiba Страницы: 34

Бренд: Toshiba Страницы: 286

Бренд: TIS Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды