Mercury MerCruiser Axius 350 MAG Скачать руководство пользователя

Страница: 78 / 151

Section 3 - On The Water

Page 70

90-864197084 NOVEMBER 2008

NOTE: This display screen is activated during VesselView calibration. The GPS system generates the displayed heading

based on magnetic North.

31413

Track Waypoint screen

Disengaging Track Waypoint Mode

1. Disengage the Track Waypoint mode by one of the following methods:

•

Press the "TRACK WAYPOINT" button on the Axius Premier Trackpad. The "TRACK WAYPOINT" button light goes off

and Axius Premier goes to Standby. The "STANDBY" light turns on

•

Turn the steering wheel hard enough to overcome the detent and Axius Premier features go into Standby.

•

Move both ERC levers back to neutral and Axius Premier goes to Standby.

•

Press either "TURN" button and Axius Premier goes to Auto Heading mode.

•

Press the "AUTO HEADING" button and Axius Premier CAN Trackpad goes to Auto Heading mode.

•

Turn off the chart plotter and Axius Premier goes to Standby.

2. You can resume the Track Waypoint heading within one minute, if the vessel has not turned too far and the "RESUME" light

is still on or flashing.

Turn Buttons or Joystick in Track Waypoint Mode

While in "TRACK WAYPOINT" mode, press the left or right "TURN" buttons on the Trackpad or use the joystick to change the

mode to "AUTO HEADING."

Auto Heading Button in Track Waypoint Mode

While in "TRACK WAYPOINT" mode, press the "AUTO HEADING" button to cause Axius Premier to change to "AUTO HEADING"

mode.

Acknowledging a Turn During a Waypoint Arrival

IMPORTANT: Track Waypoint mode does not automatically turn the boat upon arrival at a plotted waypoint.

Содержание MerCruiser Axius 350 MAG
























































































































































Результаты поиска

Содержание MerCruiser Axius 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius 350 MAG

Бренды по названию

Популярные бренды