Mercury MerCruiser Axius 350 MAG Скачать руководство пользователя

Страница: 75 / 151

Section 3 - On The Water

90-864197084 NOVEMBER 2008

Page 67

•

Pressed one of the "TURN" (course adjust) buttons with Auto Heading engaged.

a -

Port "TURN" button

b -

Starboard "TURN" button

c -

"RESUME" button

d -

"AUTO HEADING" button

Disengaging Auto Heading

1. Disengage the Auto Heading mode with any of the following actions:

•

Place the ERC handles for both engines in neutral. The "AUTO HEADING" button light turns off and the Standby light

comes on.

•

Turn the steering wheel beyond the electronic detent. The "AUTO HEADING" button light turns off and the Resume light

comes on.

•

Press the "AUTO HEADING" button on the Axius Premier CAN touchpad. The "AUTO HEADING" button light turns off

and the Standby light comes on.

a -

Port "TURN" button

b -

Starboard "TURN" button

c -

"RESUME" button

d -

"AUTO HEADING" button

2. A single horn beep sounds and the mode indicator changes from "AUTO" to "OFF".

35568

Содержание MerCruiser Axius 350 MAG
























































































































































Результаты поиска

Содержание MerCruiser Axius 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius 350 MAG

Бренды по названию

Популярные бренды