Mercury MerCruiser Axius 350 MAG Скачать руководство пользователя

Страница: 68 / 151

Section 3 - On The Water

Page 60

90-864197084 NOVEMBER 2008

7. If the ERC handles are moved to neutral, Auto Heading turns off, a single beep sounds, and the "STANDBY" light turns on.

You cannot resume your course by pressing the "RESUME" button.

a -

"OFF" button

b -

Current heading

c -

Drive positions

d -

Engine RPM

Pressing the "AUTO HEADING" button causes VesselView to displays the "AUTO HEADING" screen for three seconds. If the

VesselView "AUTO HEADING" screen does not appear, the "AUTO HEADING" screen needs to be activated in VesselView

calibration. Axius still engages whether the screen appears or not.

NOTE: If you press the "AUTO HEADING" button a second time, the Axius goes to standby mode and all lights other than

"STANDBY" turn off.

Disengage Auto Heading

1. Disengage the "AUTO HEADING" mode by any of the following actions:

•

Place the ERC levers for both engines in neutral.

•

Turn the steering wheel beyond the detent.

•

Press the "AUTO HEADING" button on the Axius touchpad. The "AUTO HEADING" button LED light turns off.

a -

Indicator light

b -

"AUTO HEADING" button

To Resume to a Heading

The "RESUME" button light turns on if the previous course heading is available to resume. The previous heading can only be

resumed within one minute of the Auto Heading being disengaged or if the boat has not turned more than 90°. You can adjust

these values during configuration.
If you disengage the Auto Heading by turning the steering wheel or if you press one of the "TURN" buttons with Auto Heading still

engaged, press the "RESUME" button to resume the previous heading.

31408

35561

Содержание MerCruiser Axius 350 MAG
























































































































































Результаты поиска

Содержание MerCruiser Axius 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius 350 MAG

Бренды по названию

Популярные бренды

Mercury MerCruiser Axius 350 MAG, Руководство пользователя

Результаты поиска

Содержание MerCruiser Axius 350 MAG

Отзывы:

Похожие инструкции для MerCruiser Axius 350 MAG

Бренды по названию

Популярные бренды