Mercury FourStroke 2.5 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 205

Mercury FourStroke 2.5 Скачать руководство пользователя страница 39

Outboard Installation

Page 1D-2

90-8M0065421 NOVEMBER 2012

Boat Horsepower Capacity

!

WARNING

Exceeding the boat's maximum horsepower rating can cause serious injury or death. Overpowering the boat can affect boat

control and flotation characteristics or break the transom. Do not install an engine that exceeds the boat's maximum power

rating.

Do not overpower or overload your boat. Most boats will carry a required capacity plate indicating the maximum acceptable

power and load as determined by the manufacturer following certain federal guidelines. If in doubt, contact your dealer or the

boat manufacturer.

U.S. COAST GUARD CAP ACITY
MAXIMUM HORSEPOWER XXX

MAXIMUM PERSON
CAPACITY (POUNDS)

XXX

MAXIMUM WEIGHT
CAPACITY

XXX

26777

Selecting Accessories for Your Outboard

Genuine Mercury Precision or Quicksilver Accessories have been specifically designed and tested for your outboard. These

accessories are available from Mercury Marine dealers.
IMPORTANT: Check with your dealer before installing accessories. The misuse of approved accessories or the use of

nonapproved accessories can damage the product.
Some accessories not manufactured or sold by Mercury Marine are not designed to be safely used with your outboard or

outboard operating system. Acquire and read the installation, operation and maintenance manuals for all your selected

accessories.

Installing the Outboard

Boat Transom Height Requirement

Measure the transom height of the boat. The anti‑ventilation plate should be 25–50 mm (1–2 in.) below the bottom of the boat.

a -

Anti‑ventilation plate

Installing the Outboard on the Transom

1. Place the outboard on the centerline of the transom.

27005

a

19053

«
...
37
38
39
40
41
...
»

Содержание FourStroke 2.5














































































































































































































Отзывы:

Нет отзывов