Mercury FourStroke 2.5 Скачать руководство пользователя страница 192 | Manualshive

Страница: 192 / 205

Mercury FourStroke 2.5 Скачать руководство пользователя страница 192

Tiller Handle

90-8M0065421 NOVEMBER 2012

Page 7B-11

7. Apply Loctite 242 Threadlocker to the fuel tank mounting bolts. Install the bolts and washers. Tighten the bolts to the

specified torque.

a -

Fuel tank

b -

Bolt and washer (M6 x 25) (3)

Tube Ref No.

Description

Where Used

Part No.

66

Loctite 242 Threadlocker

Fuel tank mounting bolts

92-809821

Description

Nm

lb‑in.

lb‑ft

Fuel tank mounting bolts (M6 x 25) (3)

6

53

8. Install the top cowl.

Throttle Cable Adjustment

Deceleration Cable

1. Rotate the grip to the "START" position.
2. Loosen the jam nuts on both throttle cables.
3. Pull the choke knob out completely.
4. Pull the outer cable jacket in the direction of the arrow.
5. Tighten the deceleration throttle cable jam nuts.
6. Gently push the inner wire. The wire should deflect approximately 1 mm (0.040 in.).
7. Push the choke knob in completely.
8. The idle screw must contact the throttle stop.

a -

Deceleration cable

b -

Throttle stop

c -

Idle screw

50010

a

b

b

b

41820

a

b

c

«
...
190
191
192
193
194
...
»

Содержание FourStroke 2.5














































































































































































































Отзывы:

Нет отзывов