Mercury 92-858058K01 страница 70 Скачать руководство пользователя

Страница: 70 / 150

Section 3 - On the Water

Page 62

90-879172181

eng

FEBRUARY 2011

3. Press the "AUTO HEADING" button to engage the Auto Heading mode. The button illuminates and a single horn beep sounds

acknowledging engagement. A double horn beep sounds if Auto Heading does not engage.

a -

"TURN" (course adjust) buttons

b -

"RESUME" button

c -

"AUTO HEADING" button

4. Display the Autopilot screen on VesselView. See

Mode Display

VesselView

5. On the Autopilot screen, the mode indicator changes from "OFF" to "AUTO".
6. The steering wheel will self‑center and be held in an electronic detent position.

NOTE: If for any reason, you must turn the steering wheel, you will need to apply sufficient force to overcome the electronic

detent.

7. Precision Pilot holds the compass heading the boat was following when the "AUTO HEADING" button was pressed and Auto

Heading engaged.

31409

Dual engine application screen shown—screens vary based on number of engines

8. To adjust your course while "AUTO HEADING" is engaged, see

Course Adjustment Using the Turn Buttons or Joystick.

9. To disengage Auto Heading refer to

Disengaging Auto Heading

10. Press the "AUTO HEADING" button a second time, Auto Heading goes to Standby mode and all lights other than "STANDBY"

turn off.

Course Adjustment Using the Turn Buttons or Joystick

While in "AUTO HEADING" mode, the "TURN" buttons (course adjust buttons) change the set course heading each time they are

pressed. Tapping the joystick left or right adjusts your course for each tap.

27700

Содержание 92-858058K01























































































































































Результаты поиска

Содержание 92-858058K01

Отзывы:

Похожие инструкции для 92-858058K01

Бренды по названию

Популярные бренды

Mercury 92-858058K01, Руководство пользователя

Результаты поиска

Содержание 92-858058K01

Отзывы:

Похожие инструкции для 92-858058K01

Бренды по названию

Популярные бренды