Mercury 92-858058K01 страница 102 Скачать руководство пользователя

Страница: 102 / 150

Section 5 - Maintenance

Page 94

90-879172181

eng

FEBRUARY 2011

Changing

You do not need to change the steering actuator and trim system oil and filter unless they become contaminated with water or

debris. A switch in the high‑pressure filter system will set a VesselView fault code to alert the operator when the hydraulic oil and

filter require changing.
Change the hydraulic oil and filter whenever the VesselView fault code is displayed.

VesselView Fault Code

Reason

Task

"Filter Dirty Fault" or "Service

Steering Filter"

Hydraulic oil filter is dirty

Change the oil and filter as soon as reasonably

possible, if not immediately

Contact your local Authorized Cummins MerCruiser Diesel Repair Facility for additional information.

High-pressure filter system

a -

Filter head with switch (switch not shown)

b -

Filter housing with filter element

Transmission Oil (Fluid) and Filter

Checking

If the drive is equipped with a drive cover, you can check the transmission oil (fluid) level through the access cover or with the

drive cover removed, if equipped.
1. If equipped with a drive cover, lift the front of the access cover from the drive cover or remove the drive cover, to access the

transmission dipstick.

a -

Access cover

b -

Molded clip

c -

Indented‑edge

37306

39506

Содержание 92-858058K01























































































































































Результаты поиска

Содержание 92-858058K01

Отзывы:

Похожие инструкции для 92-858058K01

Бренды по названию

Популярные бренды

Mercury 92-858058K01, Руководство пользователя

Результаты поиска

Содержание 92-858058K01

Отзывы:

Похожие инструкции для 92-858058K01

Бренды по названию

Популярные бренды