Mercury 8.2 H.O. ECT Скачать руководство пользователя страница 33

Страница: 33 / 94

Section 2 - Getting to Know Your Power Package

90-8M0061999

eng

MAY 2012

Page 25

7. Throttle only button ‑ Allows the boat operator to increase engine RPM for warm‑up, without shifting the engine into gear.

To engage throttle only, move the control handle into the neutral position. Press the throttle only button and move the

control handle ahead to the forward detent. The horn will sound once and the neutral light will start flashing. The horn will

sound twice when throttle only is engaged. Advance throttle to increase engine RPM. To disengage, return control handle

to neutral position and press the throttle only button. Engine RPM is limited to prevent engine damage.

8. 1 lever button ‑ Pressing the "1 LEVER" button initiates single lever mode. Single lever mode enables the throttle and shift

functions of both engines to be controlled by the port control handle. To turn off single lever mode, shift the engine into

neutral and press the "1 LEVER" button.

9. Sync button ‑ Pressing the "SYNC" button turns off or on the auto synchronization feature. Refer to

Synchronizing

Engines

a -

Neutral LEDS

b -

Troll button

c -

Transfer button

d -

Dock button

e -

Throttle only

f -

1 lever button

g -

Sync button

10. Control handle tension adjustment screw ‑ This screw can be adjusted to increase or decrease the tension on the control

handle (cover must be removed). This will help prevent unwanted motion of the handle in rough water. Turn the screw

clockwise to increase tension and counterclockwise to decrease tension. Adjust to tension desired.

11. Detent tension adjustment screw ‑ This screw can be adjusted to increase or decrease the effort to move control handle

out of detent positions (cover must be removed). Turning the screw clockwise will increase tension. Adjust to tension

desired.

a -

Detent tension adjustment screw

b -

Control handle tension adjustment screw

Synchronizing Engines

The auto synchronizing feature, when engaged, will automatically adjust all engine speeds to match the speed of the starboard

engine.
Press the "SYNC" button on the CAN trackpad to turn auto synchronization on or off. When the sync LED is yellow, the "SYNC"

button has been pressed, but the conditions are not right for auto synchronization to engage. When the sync LED turns red,

engine synchronization has been engaged. The engines will remain synchronized as long as engine speed is over 900 RPM for

two seconds, remote control handles are positioned within 10% of each other, and the engines are below 95% throttle opening.

N E

U T

R A

22133

SYNC

1 LEVER

NEUTRAL

TROLL

THROTTLE
ONLY

DOCK

TRANSFER

28556

Содержание 8.2 H.O. ECT































































































Результаты поиска

Содержание 8.2 H.O. ECT

Отзывы:

Mercury 8.2 H.O. ECT, Руководство пользователя, Страница: 33 / 94

Результаты поиска

Содержание 8.2 H.O. ECT

Отзывы: