Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 85

Страница: 85 / 107

•

Rotate the flywheel manually several times to distribute the oil in the

cylinders. Reinstall spark plugs.

•

Change the engine oil.

Gearcase

•

Drain and refill the gearcase lubricant (refer to

Gearcase Lubrication

Positioning Outboard for Storage

Store outboard in an upright (vertical) position to allow water to drain out of the

outboard.

NOTICE

Storing the outboard in a tilted position can damage the outboard. Water

trapped in the cooling passages or rain water collected in the propeller

exhaust outlet in the gearcase can freeze. Store the outboard in the full down

position.

Battery Storage

•

Follow the battery manufacturer's instructions for storage and charging.

•

Remove the battery from the boat and check water level. Charge if

necessary.

•

Store the battery in a cool, dry place.

•

Periodically check the water level and charge the battery during storage.

STORAGE

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 85 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: