Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 77

Страница: 77 / 107

2. Remove the spark plugs to inspect. Replace spark plug if electrode is

worn or the insulator is rough, cracked, broken, blistered, or fouled.

26946

3. Set the spark plug gap to specification.

26947

Spark Plug
Spark plug gap

0.9 mm (0.035 in.)

4. Before installing spark plugs, remove any dirt on the spark plug seats.

Install plugs finger‑tight, and then tighten 1/4 turn or tighten to the

specified torque.

Description

lb‑in.

lb‑ft

Spark plug

–

Timing Belt Inspection

Inspect the timing belt and have it replaced by an authorized dealer if any of the

following conditions are found.

•

Cracks in the back of the belt or in the base of the belt teeth.

•

Excessive wear at the roots of the cogs.

•

Rubber portion swollen by oil.

•

Belt surfaces roughened.

MAINTENANCE

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 77 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: