Mercury 4.3 TKS series Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 109

Mercury 4.3 TKS series Скачать руководство пользователя страница 86

Section 5 - Storage

Page 78

90-8M0113857

eng

DECEMBER 2015

7. Verify that water is draining from each opening. If not, use the

Three Point Manual Drain System

instructions.

a -

Port side drain location

b -

Starboard side drain location

8. Allow the system to drain for a minimum of ten minutes. Pump air as necessary to keep the green indicators extended.
9. Crank the engine over slightly with the starter motor to purge any water trapped in the seawater pump. Do not allow the

engine to start.

10. Remove the air pump from the air manifold and return it to the mounting bracket.
11. Mercury MerCruiser recommends leaving the drain system open while transporting the boat or while performing other

maintenance. This helps ensure that all water is drained.

12. Before launching the boat, pull up on the manual release valve. Verify that the green indicators are no longer extended.

a -

Green indicators

Manual Single‑Point Drain System (Alpha)

Boat in the Water

1. Close the seacock (if equipped) or remove and plug the water inlet hose.

a.

4.3 MPI ECT—

Remove the blue plug at the distribution housing at the lower front right corner of the engine.

45951

4.3 MPI ECT

a

b

6133

a

6135

«
...
84
85
86
87
88
...
»

Содержание 4.3 TKS series














































































































Отзывы:

Нет отзывов