Mercury 4.3 TKS series Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 109

Mercury 4.3 TKS series Скачать руководство пользователя страница 57

Section 4 - Maintenance

90-8M0113857

eng

DECEMBER 2015

Page 49

Bravo Two Propeller Removal

!

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the water with a propeller installed.

Before installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the

engine from starting. Place a block of wood between the propeller blade and the anti‑ventilation plate.

1. Place a wood block between the propeller blade and anti‑ventilation plate to prevent rotation. Straighten bent tabs on tab

washer.

2. Turn propeller shaft nut counterclockwise to remove nut.
3. Slide tab washer, spline washer, propeller, and thrust hub off propeller shaft.

Bravo Two Propeller Installation

IMPORTANT: The selected propeller's rotation must match the forward gear direction of propeller shaft rotation.
1. Liberally coat the propeller shaft spline with one of the following Quicksilver lubricants.

Tube Ref No.

Description

Where Used

Part No.

95

2-4-C with PTFE

Propeller shaft splines

92-802859A 1

Extreme Grease

Propeller shaft splines (saltwater only)

8M0071842

NOTE: Extreme Grease is for saltwater applications only.

2. Install the propeller with the attaching hardware as shown.
3. Tighten the propeller nut to the specified torque.

Bravo Two

a -

Propeller shaft splines

b -

Forward thrust hub

c -

Propeller

d -

Spline washer

e -

Tab washer

f -

Propeller nut

NOTE: The torque stated is a minimum torque value.

Description

Nm

lb‑in.

lb ft

Bravo Two propeller nut

81

–

60

Then align tabs with grooves

4. Continue to tighten the propeller nut until the three tabs on the tab washer align with the grooves on the spline washer.
5. Bend the three tabs down into the grooves.

a -

Propeller

b -

Tab washer

c -

Drive sleeve adapter

d -

Tab bent down

e -

Propeller nut

8566

a

b

c

f

d

e

a

b

c

d

e

4750

«
...
55
56
57
58
59
...
»

Содержание 4.3 TKS series














































































































Отзывы:

Нет отзывов