Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 98

Страница: 98 / 159

Battery Inspection

The battery should be inspected at periodic intervals to ensure proper engine

starting capability.
IMPORTANT: Read the safety and maintenance instructions which accompany

your battery.

1. Turn off the engine before servicing the battery.
2. Ensure the battery is secure against movement.
3. Battery cable terminals should be clean, tight, and correctly installed.

Positive to positive and negative to negative.

4. Ensure the battery is equipped with a nonconductive shield to prevent

accidental shorting of battery terminals.

Battery Information (All Batteries Including DTS)

WARNING

Failure to properly secure the battery leads can result in a loss of power to

the Digital Throttle and Shift (DTS) system, leading to serious injury or death

due to loss of boat control. Secure the battery leads to the battery posts with

hex nuts to avoid loose connections.

•

Do not use deep cycle batteries. The engine must use a marine starting

battery with 1000 MCA, 800 CCA, or 180 Ah rating.

•

When connecting the engine battery, use hex nuts to secure the battery

leads to the battery posts. Tighten the nuts to the specified torque.

Description

lb‑in.

lb‑ft

Hex nuts

13.5

120

–

MAINTENANCE

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 98 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: