Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 96

Страница: 96 / 159

Assemble steering link rod to steering cable with two flat washers and

self‑locking nylon insert locknut. Tighten locknut until it seats, then back nut off

1/4 turn.
Assemble steering link rod to engine with special washer head bolt and

self‑locking nylon insert locknut. First torque bolt, then torque locknut to

specifications.

Fuse Replacement

IMPORTANT: Always carry spare 5 and 20‑amp fuses.
The electrical wiring circuits on the outboard are protected from overload by

fuses in the wiring. If a fuse is blown, try to locate and correct the cause of the

overload. If the cause is not found, the fuse may blow again.
Open the fuse holder and look at the silver colored band inside the fuse. If the

band is broken, replace the fuse. Replace fuse with a new fuse with the same

rating.

a -

Good fuse

b -

Blown fuse

c -

14 pin remote control harness/cowl trim switch/main power relay ‑

15‑amp fuse

d -

Ignition coil circuit ‑ 20‑amp fuse

e -

SmartCraft data bus circuit ‑ 5‑amp fuse

f -

Diagnostics terminal ‑ 2‑amp fuse

g -

Spare fuse ‑ 20‑amp fuse

h -

Fuel injectors/direct injectors/oil pump/PCM ‑ 20‑amp fuse

23793

MAINTENANCE

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 96 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: