Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 93

Страница: 93 / 159

Fuel System

WARNING

Fuel is flammable and explosive. Ensure that the key switch is off and the

lanyard is positioned so that the engine cannot start. Do not smoke or allow

sources of spark or open flame in the area while servicing. Keep the work

area well ventilated and avoid prolonged exposure to vapors. Always check

for leaks before attempting to start the engine, and wipe up any spilled fuel

immediately.

Before servicing any part of the fuel system, stop the engine and disconnect

the battery. Drain the fuel system completely. Use an approved container to

collect and store fuel. Wipe up any spillage immediately. Material used to

contain spillage must be disposed of in an approved receptacle. Any fuel

system service must be performed in a well‑ventilated area. Inspect any

completed service work for sign of fuel leakage.

FUEL LINE INSPECTION

Visually inspect the fuel line and primer bulb for cracks, swelling, leaks,

hardness, or other signs of deterioration or damage. If any of these conditions

are found, the fuel line or primer bulb must be replaced.

FUEL FILTER REPLACEMENT

Removal

Use fuel filter tool 91‑896661, or the shaft of a screwdriver, between the lugs on

the filter cap and unscrew the filter.

a -

Filter

b -

O‑rings

29594

MAINTENANCE

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 93 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: