Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 88

Страница: 88 / 159

2. Lift rear of cowl and disengage front hook.

29468

INSTALLATION

1. Engage the front hook and push cowl back over the cowl seal.
2. Push cowl down and move the rear latch lever down to lock.

Cleaning Care for Top Cowl

IMPORTANT: Dry wiping (wiping the plastic surface when it is dry) will result in

minor surface scratches. Always wet the surface before cleaning. Follow the

cleaning and waxing procedure.

CLEANING AND WAXING PROCEDURE

1. Before washing, rinse the top cowl with clean water to remove the dirt and

dust that may scratch the surface.

2. Wash the top cowl with clean water and a mild nonabrasive soap. Use a

soft, clean cloth when washing.

3. Dry thoroughly with a soft, clean cloth.
4. Wax the surface using a nonabrasive automotive polish (polish designed

for clear coat finishes). Remove the applied wax by hand using a soft,

clean cloth.

Flywheel Cover Removal and Installation

REMOVAL

Lift the cover off the three mounting pins.

MAINTENANCE

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 88 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: