Mercury 115 Pro XS FourStroke Скачать руководство пользователя страница 105

Страница: 105 / 159

Alternator Belt Inspection

WARNING

Inspecting the belts with the engine running may cause serious injury or

death. Turn off the engine and remove the ignition key before adjusting

tension or inspecting belts.

Inspect the alternator belt and have it replaced by an authorized dealer if any of

the following conditions are found.

•

Cracks or deterioration in the rubber portion of the belt.

•

Belt surfaces rough or uneven.

•

Signs of wear on edges or outer surfaces of belt.

29477

Lubrication Points

1. Lubricate the following with Extreme Grease or 2‑4‑C with PTFE.

Tube Ref

No.

Description

Where Used

Part No.

Extreme Grease

Propeller shaft

8M0071842

2-4-C with PTFE

Propeller shaft

92-802859A 1

MAINTENANCE

eng

Содержание 115 Pro XS FourStroke
































































































































































Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы:

Mercury 115 Pro XS FourStroke, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 105 / 159

Результаты поиска

Содержание 115 Pro XS FourStroke

Отзывы: