Mercury Racing HP1200 SCi Dry Sump Скачать руководство пользователя страница 100

Страница: 100 / 106

TROUBLESHOOTING

Insufficient Engine Temperature

Possible Cause

Remedy

Faulty water thermostat.

Replace water thermostat.

Faulty gauge or sender.

Test with shop gauge; test sender.

Faulty oil thermostat.

Replace.

Excessive Engine Temperature

Possible Cause

Remedy

Seacock closed.

Open.

Charge Air Cooler plugged with foreign

material.

Clean Charge Air Cooler.

Seawater pump drive belt loose or in

poor condition.

Replace or adjust belt.

Seawater pickups obstructed.

Inspect.

Faulty thermostat.

Replace.

Oil cooler cores plugged with foreign

material.

Clean cooler cores.

Faulty seawater pickup pump.

Repair.

Seawater discharge restricted or

plugged.

Clean exhaust elbows.

Faulty gauges or senders.

Test with shop gauges; test senders.

Aerated water supply to water pick‑up. Place water pick‑up in a non‑aerated

water supply.

Содержание HP1200 SCi Dry Sump











































































































Результаты поиска

Содержание HP1200 SCi Dry Sump

Отзывы:

Бренды по названию

Популярные бренды

Mercury Racing HP1200 SCi Dry Sump, Инструкция по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание HP1200 SCi Dry Sump

Отзывы:

Бренды по названию

Популярные бренды