manualshive.com logo in svg

Mercury Racing 1350 STERNDRIVE, Эксплуатация, обслуживание и гарантия, Страница: 29 / 73

Поделиться
Скачать
Mercury Racing 1350 STERNDRIVE Скачать руководство пользователя страница 29

3 - S

PECIFICATIONS

 

24

90-8M0114811   JANUARY  2016

Coolant thermostat is fully open at

temperature. . . . . . . . . . . . . .

85 °C (185 °F)

Minimum water pressure supplied to the

engine. . . . . . . . . . . . . . . . .

170 kPa (25 psi) at 6500

RPM

Maximum water pressure supplied to the

engine. . . . . . . . . . . . . . . . .

241 kPa (35 psi) at 6500

RPM

Minimum oil pressure at idle (hot). . . .

1 bar (14.5 psi)

Minimum oil pressure at 6500 RPM (hot)

3 bar (43.5 psi)

Maximum oil temperature at 6500 RPM

(hot). . . . . . . . . . . . . . . . . .

140 °C (284 °F)

F

UEL

 R

EQUIREMENTS

Use a major brand of unleaded gasoline, preferably without alcohol.

Mercury Marine recommends fuels that contain fuel injector cleaner

for added internal cleanliness.

!

 WARNING

Fuel leakage is a fire or explosion hazard, which can cause serious

injury or death. Periodically inspect all fuel system components for

leaks, softening, hardening, swelling, or corrosion, particularly after

storage. Any sign of leakage or deterioration requires replacement

before further engine operation.

NOTICE

The use of improper fuel can cause serious damage to the engine.

Damage  resulting  from  the  use  of  improper  fuel  is  considered

engine misuse and is not covered under the limited warranty. Use

only the recommended fuel in the engine.

OCTANE REQUIREMENTS (U.S./CANADA)

Engine

FUEL TYPE

MINIMUM POSTED

OCTANE

1350

QC4v

Unleaded

(R+M) ÷ 2 = 91 or RON

= 98*

NOTE: *Research Octane Number

1350 OCTANE REQUIREMENTS (OUTSIDE THE U.S./CANADA)

Engine

FUEL TYPE

MINIMUM POSTED

OCTANE

1350

QC4v

Unleaded

1.

(R+M) ÷ 2 = 91 or

RON = 98*

NOTE: *Research Octane Number

USING REFORMULATED (OXYGENATED) FUELS (USA ONLY)

This type of fuel is required in certain areas of the U.S. The two types

of oxygenates used in these fuels are alcohol (ethanol) or ether

(MTBE or ETBE). If ethanol is the oxygenate that is used in the

gasoline in your area, refer to the 

Fuel containing alcohol

 section.

These reformulated fuels are acceptable for use in your Mercury

engine.

1.

Mercury Racing does not recommend using leaded gasoline. Leaded gasoline is acceptable in areas where unleaded gasoline is not available; however, lead particles may build up in the

exhaust passages and/or the combustion chambers.

Содержание 1350 STERNDRIVE










































































Отзывы:

Нет отзывов