MerCruiser Axius 350 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 149

background image

Section 5 - Maintenance

90-8M0053363

eng

NOVEMBER 2010

Page 85

Date

Maintenance Performed

Engine Hours

Engine Oil

NOTICE

Discharge of oil, coolant, or other engine/drive fluids into the environment is restricted by law. Use caution not to spill oil, coolant,

or other fluids into the environment when using or servicing your boat. Be aware of the local restrictions governing the disposal

or recycling of waste, and contain and dispose of fluids as required.

Checking

1. Stop the engine. Allow approximately 5 minutes for the oil to drain into the oil pan. The boat must be at rest in the water.
2. Remove the dipstick. Wipe clean and reinstall fully into the dipstick tube. Wait 60 seconds to allow trapped air to vent.

NOTE: Ensure that dipstick is installed with oil level indication marks facing the rear of the engine (flywheel end).

a -

Dipstick tube

IMPORTANT: Add the specified engine oil to bring the level up to, but not over, the full or OK range mark on the dipstick.

3. Remove the dipstick and observe the oil level. Oil level must be between full or OK range and add. Reinstall dipstick into

dipstick tube.

Filling

IMPORTANT: Do not overfill the engine with oil.

IMPORTANT: Always use the dipstick to determine the exact quantity of oil or fluid required.

a

6095

«
...
91
92
93
94
95
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Бренд: JetCat Страницы: 74

Бренд: O.S. engine Страницы: 19

E-II SGM H Series

Бренд: YASKAWA Страницы: 408

Бренд: RCGF Страницы: 22

Бренд: Grundfos Страницы: 25

Бренд: ACM Страницы: 36

Бренд: Quectel Страницы: 165

Бренд: Leadshine Technology Страницы: 11

Бренд: O.S. engine Страницы: 17

Бренд: O.S. engine Страницы: 20

Бренд: Detroit Diesel Страницы: 195

Бренд: Honda Страницы: 8

Бренд: Honda Страницы: 2

Бренд: Honda Страницы: 149

Бренд: ST Страницы: 281

Бренд: Alemlube Страницы: 16

Бренд: Briggs & Stratton Страницы: 6

Бренд: Wood-mizer Страницы: 226

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды