MerCruiser Axius 350 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 149

background image

Section 3 - On The Water

Page 72

90-8M0053363

eng

NOVEMBER 2010

8. If you are not in a previously set waypoint arrival zone, "WAYPOINT SEQUENCE" mode starts auto sequencing to the

waypoints in the route. Acknowledge that you understand the information presented by the pop‑up screen warning and press

the enter button—the button with a check mark symbol.

31412

Pop-up screen warning

9. Press the "TRACK WAYPOINT" button. The "WAYPOINT SEQUENCE" button light turns on and a single horn beep sounds.
10. Press the "TRACK WAYPOINT" button a second time to put Axius Premier in Standby mode. All lights other than "STANDBY"

turn off.

Cruise Control

The VesselView system features integrated throttle cruise control (cruise), which allows the operator to limit the peak RPM of

choice below Wide Open Throttle (WOT). This feature requires VesselView. Refer to the owner's manual provided with your

VesselView for operation instructions.
These additional notes are exclusive to your package:
•

You can change or disengage cruise through the screen at any time.

•

Cruise resets when the key is turned off.

•

If the cruise limit is changed while the levers are at WOT, cruise gradually changes to the new speed.

•

Cruise does not disengage if the ERC levers are at a higher engine speed than the actual RPM. Bring the levers back to the

forward detent to disengage.

Contingent Operations

Port Engine–Only Operation

The force feedback feature of the steering wheel is only available when the starboard key switch is in the on position. If the starboard

key switch is off or there has been damage to the starboard electrical system, the port control system monitors the steering wheel.
If only the port side is operational, or only the port key switch is in the on position, the force feedback system will not provide end

stops for the steering wheel. In this case, the drive will turn in the direction of steering wheel rotation until the mechanical limits of

the drive are reached.

NOTE: If the port electrical system is damaged, the steering wheel will operate normally with complete force feedback and end

stops.

Note that joystick is not available in single‑engine operation. However, Axius features redundant trackpad systems, so Auto

Heading mode is still available during single‑engine operation.

«
...
78
79
80
81
82
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Бренд: Quectel Страницы: 71

Бренд: Yanmar Страницы: 224

Char-Lynn H Series

Бренд: Eaton Страницы: 13

695D/925 Series

Бренд: Wisco Industries Страницы: 6

Бренд: Briggs & Stratton Страницы: 6

X Trainer 300 2T 2015

Бренд: Beta Motorcycles Страницы: 117

Бренд: A'OK Страницы: 7

Бренд: SunStar Страницы: 86

Бренд: SSANGYONG Страницы: 16

Бренд: SSANGYONG Страницы: 42

Бренд: Fagor Страницы: 174

Бренд: Honda Страницы: 222

Бренд: Briggs & Stratton Страницы: 11

CNC Meldas HC Series

Бренд: Mitsubishi Страницы: 52

Бренд: Packard Страницы: 16

Бренд: Hacker Страницы: 38

Бренд: Yanmar Страницы: 394

Бренд: Zenith Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды