MerCruiser Axius 350 Скачать руководство пользователя страница 77

Страница: 77 / 149

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 69

2. You can resume the Track Waypoint heading within one minute, if the vessel has not turned too far and the "RESUME" light

is still on or flashing.

Turn Buttons or Joystick in Track Waypoint Mode

While in "TRACK WAYPOINT" mode, press the left or right "TURN" buttons on the Trackpad or use the joystick to change the

mode to "AUTO HEADING."

Auto Heading Button in Track Waypoint Mode

While in "TRACK WAYPOINT" mode, press the "AUTO HEADING" button to cause Axius Premier to change to "AUTO HEADING"

mode.

Acknowledging a Turn During a Waypoint Arrival

IMPORTANT: Track Waypoint mode does not automatically turn the boat upon arrival at a plotted waypoint.
1. When the boat enters a waypoint arrival zone as indicated by the chart plotter, a short horn beep sounds and the "WAYPOINT

SEQUENCING" button light starts blinking to inform the operator to make a turn.

a -

Indicator light

b -

"WAYPOINT SEQUENCE" button

2. If the Waypoint Sequence mode has not been engaged, the "WAYPOINT SEQUENCE" icon light blinks at the arrival zone.

31411

Waypoint Sequence icon light

35575

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды