MerCruiser Axius 350 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 149

background image

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 59

•

Press the "AUTO HEADING" button on the Axius touchpad. The "AUTO HEADING" button LED light turns off.

a -

Indicator light

b -

"AUTO HEADING" button

To Resume to a Heading

The "RESUME" button light turns on if the previous course heading is available to resume. The previous heading can only be

resumed within one minute of the Auto Heading being disengaged or if the boat has not turned more than 90°. You can adjust

these values during configuration.
If you disengage the Auto Heading by turning the steering wheel or if you press one of the "TURN" buttons with Auto Heading still

engaged, press the "RESUME" button to resume the previous heading.

Changing VesselView Mode Display Times

All modes display a screen on VesselView for three seconds by default. The length of time that a screen is visible in VesselView

can be changed from no display at all, display up to 10 seconds, or display the screen until changed.
To change the display time:
1. Open VesselView.
2. Select Setting.
3. Select Screen Options.
4. Select the mode you want to change.
5. Select the option you desire.
6. Press × to exit.

Skyhook

!

WARNING

A rotating propeller, a moving boat, or a device attached to a moving boat can cause serious injury or death to people in the

water. When Skyhook is engaged, the propellers rotate and the boat moves to maintain the position of the boat. Stop the engines

immediately whenever anyone is in the water near the boat.

Skyhook uses GPS and the compass heading information to control the throttle, gear position and steering to maintain the boat's

position within approximately 3 m (10 ft).
The Skyhook feature can hold your boat nearly stationary, for example, while you wait for a space at the fuel dock, or while waiting

for a bridge to open. You can also use Skyhook to maintain your boat's position when the water is too deep for an anchor.
Skyhook should not be used when the boat is next to a dock, or any other object, including other anchored boats. Because Skyhook

holds the boat in an approximate position, not a precise one, it can cause your boat to collide with objects close to the boat causing

damage to the boat and the nearby objects. Occasionally the Skyhook system may apply a brief surge in power while holding a

position. This may cause a person standing near the edge of the boat to lose their balance and fall.

35561

a

b

«
...
65
66
67
68
69
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Бренд: Kubota Страницы: 138

Бренд: Evinrude & Johnson Страницы: 349

Бренд: V2 Страницы: 17

Бренд: Volkswagen Страницы: 64

Бренд: TecumsehPower Страницы: 24

Бренд: Tecumseh Страницы: 20

Бренд: Tecumseh Страницы: 8

Бренд: Central Machinery Страницы: 30

Бренд: DUROMAX Страницы: 70

Бренд: Omron Страницы: 18

Бренд: Omron Страницы: 438

Бренд: Louvolite Страницы: 2

Бренд: ARO Страницы: 2

Бренд: ARO Страницы: 8

Concept engines

Бренд: RB Страницы: 19

Бренд: Honda Страницы: 182

Бренд: Stober Страницы: 48

Бренд: O.S. engine Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды