MerCruiser Axius 350 Скачать руководство пользователя страница 34

Страница: 34 / 149

Section 2 - Getting to Know Your Power Package

Page 26

90-8M0053363

eng

NOVEMBER 2010

ERC Trim Control

WARNING

Excessive trim can cause serious injury or death at high speeds. Use caution when trimming the sterndrive, and never trim out

beyond the gimbal ring support flanges while the boat is underway or at engine speeds above 1200 RPM.

Some ERC's will have a single button for trimming both sterndrives simultaneously or may have separate buttons for each

sterndrive unit.
For best performance trim the sterndrive unit so that the boat bottom is at a 3‑5° angle to the water.

3 - 5

mc79528

Trimming the sterndrive unit up (out) can:
•

Generally increase top speed

•

Increase clearance over submerged objects or a shallow bottom

•

Cause the boat to accelerate and plane off slower

•

In excess, cause boat porpoising (bouncing) or propeller ventilation

•

Cause engine overheating, if trimmed up (out) to a point where any cooling water intake holes are above the water line

mc78529

Trimming the sterndrive unit down(in) can:
•

Causes the boat to accelerate and plane off quicker

•

Generally improve the ride in choppy water

•

In most cases, reduce boat speed

•

In excess, can cause bow steering (unexpected turning) by lowering the bow of the boat so that it plows the waterline while

on plane.

mc79530

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды