MerCruiser Axius 350 Скачать руководство пользователя страница 142

Страница: 142 / 149

Section 7 - Troubleshooting

Page 134

90-8M0053363

eng

NOVEMBER 2010

Low Engine Oil Pressure

Possible Cause

Remedy

Insufficient oil in crankcase.

Check and add oil.

Excessive oil in crankcase (causing it to

become aerated).

Check and remove required amount of oil. Check for cause of excessive oil

(improper filling).

Diluted or improper viscosity oil.

Change oil and oil filter, using correct grade and viscosity oil. Determine cause

for dilution (excessive idling).

Battery Will Not Recharge

Possible Cause

Remedy

Excessive current draw from battery.

Turn off non‑essential accessories.

Alternator drive belt loose or in poor condition.

Replace and/or adjust.

Unacceptable battery condition.

Test battery, replace if necessary.

Loose or dirty electrical connections or damaged

wiring.

Check all associated electrical connections and wires (especially

battery cables). Clean and tighten faulty connections. Repair or replace

damaged wiring.

Faulty alternator

Test alternator output, replace if necessary.

Joystick

Symptom

Remedy

The joystick does not control the boat.

One or both remote controls are not in neutral. Put both remote

controls in neutral.
One or both engines are not running. Start the engine or engines.

Response to joystick input is erratic, or the joystick

operates independent of input.

Ensure there are no radios or other sources of electronic or magnetic

interference near the joystick.

The joystick does not function properly and a fault code

is set.

Check VesselView for Guardian fault codes that indicate reduced

engine power. If found, have the system checked by your authorized

Mercury MerCruiser dealer.

The joystick does not work; No fault code is set and

cruise control engaged.

Disengage cruise control.

Electronic Remote Controls

Symptom

Remedy

The ERC (electronic remote control) lever is too hard or

too easy to move out of neutral detent.

Adjust detent tension. See

Section 2, Dual Handle Electronic

Remote Control with DTS Trackpad Features and Operation

The ERC lever has too much or too little resistance

through its range of motion.

Adjust the handle tension screw. See

Section 2, Dual Handle

Electronic Remote Control with DTS Trackpad Features and
Operation

The ERC lever increases engine RPM, but does not

engage gears and the boat does not move.

Key off and key on.
Check the "Throttle Only" button on the DTS trackpad. Put the ERC

levers in neutral and push the button to disengage, if the light is on.
Engage gears manually. See

Section 3, Gear Engagement—

Emergency Procedure

Contact your authorized Mercury MerCruiser dealer.

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды