Mendota FV46 Скачать руководство пользователя страница 70

Страница: 70 / 96

85-03-01108

FV46

Page

Vent Damper Adjustments

This fireplace is equipped with a vent damper system that can be adjusted using the glass latch tool. Locate damper adjustment

rod above the glass frame in convection chamber at the center. If this fireplace’s vent is terminated horizontally, DO NOT CLOSE

the vent damper completely. Adjust position of damper by judging the flame characteristics after 20 minutes of burn time. If the

flames ghost off burners or if sooting occurs [in LPG units], open the vent damper FULLY and work backwards in increments to

determine the correct

damper position for that

particular installation.
Look into the convection air

cavity and note the Damper

Position Indicator. Hook

glass latch tool in the hole

at the end of the damper

rod, pull outward about

1/8” and turn clockwise to

close the vent damper,

release. The base of the

damper adjustment rod has a pointer that indicates the position of the damper.

4.12

LOG SET/ MEDIA INSTALLATION

Four distinctive wood species log sets are available as options for this model Fireplace.
1.

Norway Spruce Log Set

White Oak Log Set (not shown)

Birch Log Set

Premium Fiber Oak Log

Figure 4-16 Norway Spruce Logs

Figure 4-17 Birch Logs

Figure 4-18 Premium Fiber

Oak Logs

Installation Instructions for each log set are included with the individual log set. Follow those instructions to install one log set.

Note: Installer, save and give the copy of the Log Set Installation Instructions to the homeowner for future

references.

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды